Korzystając ze strony wyrażasz zgodę na używanie cookie, zgodnie z aktualnymi ustawieniami przeglądarki. OK

V. Moni, P. Klouda, J. Blata, F. Helebrant
The application for a prediction of the coal spontaneous ignition - PREDISAM
DOI 10.1515/mspe-2017-0011
Abstract: The article follows the research of the project number TA01020351 called “The research of possibilities when predicting steam origin and consequent spontaneous ignition of brown coal fuels” which was researched with the support of the Technological Agency in the Czech Republic in 2011-2014 in the connection with a realized technical research. Therefore, it gives a summary information about the evaluation of the risk degree for the origin of spontaneous ignitions of the brown coal. The presented way of evaluation is based on a numeric expression of a value for MHU criteria – the point load of particular indicators is added together with other results gained from this research project. Then, more information is taken from companies running the dumps of brown coal products – both for suppliers (mining companies) and big consumers (power engineering). The complex knowledge about prediction of the origin of the spontaneous ignition enables to make an early response to eliminate a threat of mining fire in open pit mines or on the dumps of coal products. Consequently, it reduces the risk of fire and breakdowns of transportation means DPD, heavy machines and preparation plants. The working injuries are reduced as well – burns by coal in fire or inhalation of gas products from imper-fect combustion.
Keywords: spontaneous ignition, brown coal, dumps, evaluation of prediction to spontaneous ignition
Read article »

K. Ćwirko, A. Kalbarczyk-Jedynak
Performance and selectivity of ceramic membranes in the ultrafiltration of model emulsion in saline
DOI 10.1515/mspe-2017-0012
Abstract: Oily wastewaters from different onshore and offshore installations and from maritime transport pose a serious threat to the environment so they must be treated by multistage separation also including membrane processes. The main advantages of such membranes are high performance and selectivity, high resistance for temperature and pressure, resistance for acids, bases and solvents, long service life and for application – significant reduction of industries and transport environmental impact. This work presents the results of the process of separation of oil from the emulsion with NaCl addition. Research was performed with a use of laboratory installation with ceramic 300 kDa membrane. The analysis concerned performance and selectivity of a membrane in the function of time and test results have been subsequently compared with the requirements of the IMO.
Keywords: ceramic membranes, ultrafiltration, selectivity of membranes, oil emulsions, oily wastewaters, saline emul-sions, bilge water, ballast water
Read article »

О.Е. Shabaev, I.I. Bridun, О.К. Moroz
Diagnostics of breakdown of cutting head of the Π110-04 type heading machine
DOI 10.1515/mspe-2017-0013
Abstract: The operation of a heading machine with an out-of-work cutting tool can cause essential reduction of the machine element resource. The diagnostics of the cutting tool breakdown on the longitudinal axial cutting head in the real – time mode can be implemented on the basis of the spectral decomposition of the current of the cutting engine of the cutting unit. The ratio of the coefficients of the spectral decomposition corresponding to the cutting head rotation frequency and its threefold value can be the parameter under the diagnosis.
Keywords: heading machine, cutting unit, cutting-tool, abrasive wear, diagnostics
Read article »

T. Cepowski
Prediction of the main engine power of a new container ship at the preliminary design stage
DOI 10.1515/mspe-2017-0014
Abstract: The paper presents mathematical relationships that allow us to forecast the estimated main engine power of new container ships, based on data concerning vessels built in 2005-2015. The presented approximations allow us to estimate the engine power based on the length between perpendiculars and the number of containers the ship will carry. The approximations were developed using simple linear regression and multivariate linear regression analysis. The presented relations have practical application for estimation of container ship engine power needed in preliminary parametric design of the ship. It follows from the above that the use of multiple linear regression to predict the main engine power of a container ship brings more accurate solutions than simple linear regression.
Keywords: container ship, design parameters, preliminary design stage, power, main engine power, length between perpendiculars, number of containers, TEU capacity, design, simple regression, multiple regression, approximation
Read article»

Z. Respondek
The problems of maintenance of drainage devices within municipal and district roads
DOI 10.1515/mspe-2017-0015
Abstract: The article presents technical aspects of maintenance of proper condition of drainage devices of public roads, and municipal and district roads in particular. The importance of road drainage is discussed, basic surface drainage devices discussed together with their location within the road. With use of actual examples we indicated the typical errors made during repairs and overhauls of the road, that have the consequence of disrupted continuity of drainage or the risk of quick loss of functions of drainage devices. The results of survey of technical condition of roadsides and the drainage device within a selected rural municipality were presented, indicating main problems of road keepers connected with keeping the drainage infrastructure in appropriate condition. The need of growing awareness in planning and designing road investment was indicated in the field of consequences of performing insufficient drainage.
Keywords: road drainage, maintenance of public roads, drainage devices
Read article »

O. Klyus, O. Bezyukov
Use of water-fuel mixture in diesel engines at fishing vessels
DOI 10.1515/mspe-2017-0016
Abstract: The paper presents the laboratory test results determining physical parameters of fuel mixture made up of petroleum diesel oil, rapeseed oil methyl esters (up to 20%) and water (up to 2.5%). The obtained parameters prove that adding biocomponents (rapeseed oil methyl esters) and water to fuel does not result in deterioration of their physical and chemical properties and are comparable to base fuel parameters, namely petroleum diesel oil. The mixture was a subject of bench testing with the use of a self-ignition engine by means of precatalytic fuel treatment. The treatment process consisted in fuel – catalytically active material direct contact on the atomizer body. At the comparable operational parameters for the engine, the obtained exhaust gases opacity was lower up to 60% due to the preliminary fuel mixture treat-ment in relation to the factory-made fuel injection system using petroleum diesel oil.
Keywords: diesel engine, preliminary fuel treatment, water-fuel mixture
Read article »

A. Jakubowski
Technology of producing the contact connections of superconductor metal - sheathed cable
DOI 10.1515/mspe-2017-0017
Abstract: The technology of producing the current contact connections on the superconductor cable edges is presented. This lead cable is used as one of the major elements of the magnetic system in thermonuclear reactor construction, actuality for modern world energy. The technology is realized by the radial draft of metal thin-walled tube on the conductor’s package. The filling of various profiles by round section wire is optimized. Geometrical characteristics of the dangerous crosssection (as a broken ring) of thin-walled tube injured by the sector cut-out are accounted. The comparative strength calculation of the solid and injured tubes at a longitudinal compression and lateral bending is acted. The radial draft mechanism of cylindrical thin-walled sheath with the wire packing is designed. The necessity to use the nonlinear theory for the sheaths calculate is set. The resilient cooperation of wires as the parallel located cylinders with the contact stripes of rectangular form is considered.
Keywords: superconductor cable, contact connection, wire, packing, thin-walled tube, radial draft, contact
Read article »

A. Repelewicz
Rational increasing of efficiency of sacral buildings
DOI 10.1515/mspe-2017-0018
Abstract: The paper presents the possibilities of increasing energy efficiency of sacral buildings. Churches in the Zawiercie pastoral district of the Archdiocese of Czestochowa have been used as examples of typical sacral buildings of low energy efficiency. Such structures need to be thermally insulated during their use. Certain possibilities of raisingthe energy efficiency of churches have been presented. The paper describes different systems: increasingof wall and roof insulation, installation of new windows, and modern heating systems. Installation of a new heating system has been considered the most effective and the easiest to be implemented one.
Keywords: sacralbuildings, church buildings, thermal insulation, heating systems
Read article »

T. Szelangiewicz, K. Żelazny
Prediction power propulsion on the ship at the stage of preliminary design. Part I: Forecasting method for power propulsion on the ship at the stage of preliminary design
DOI 10.1515/mspe-2017-0019
Abstract: During the design of the ship the most important decisions are made at the stage of preliminary design. One of the most important design parameters assumed by the shipowner is its service speed in real weather conditions occurring in the shipping line. For this speed, at the stage of preliminary design, when are known only to the basic geometric parameters of the ship and its motor power should be determined. In practice, design, power propulsion is determined with a very approximate formulas but for the speed in calm water. Only after the project contract and the signing of the contract are carried out by means of resistance and self-propulsion of model test. The article presents the concept of the method for determining the power propulsion for the assumed service speed, which depends only on the basic geometric parameters of the ship's hull.
Keywords: power propulsion, service speed, preliminary design
Read article »

S. Berczyński, D. Grochała, Z. Grządziel
Modeling of surface geometric structure state after intergrated formed milling and burnishing
DOI 10.1515/mspe-2017-0020
Abstract: The article deals with computer-based modeling of burnishing a surface previously milled with a spherical cutter. This method of milling leaves traces, mainly asperities caused by the cutting crossfeed and cutter diameter. The burnishing process – surface plastic treatment – is accompanied by phenomena that take place right in the burnishing ballmilled surface contact zone. The authors present the method for preparing a finite element model and the methodology of tests for the assessment of height parameters of a surface geometrical structure (SGS). In the physical model the workpieces had a cuboidal shape and these dimensions: (width × height × length) 2×1×4.5 mm. As in the process of burnishing a cuboidal workpiece is affected by plastic deformations, the nonlinearities of the milled item were taken into account. The physical model of the process assumed that the burnishing ball would be rolled perpendicularly to milling cutter linear traces. The model tests included the application of three different burnishing forces: 250 N, 500 N and 1000 N. The process modeling featured the contact and pressing of a ball into the workpiece surface till the desired force was attained, then the burnishing ball was rolled along the surface section of 2 mm, and the burnishing force was gradually reduced till the ball left the contact zone. While rolling, the burnishing ball turned by a 23° angle. The cumulative diagrams depict plastic deformations of the modeled surfaces after milling and burnishing with defined force values. The roughness of idealized milled surface was calculated for the physical model under consideration, i.e. in an elementary section between profile peaks spaced at intervals of crossfeed passes, where the milling feed fwm = 0.5 mm. Also, asperi-ties after burnishing were calculated for the same section. The differences of the obtained values fall below 20% of mean values recorded during empirical experiments. The adopted simplification in aftermilling SGS modeling enables substantial acceleration of the computing process. There is a visible reduction of the Ra parameter value for milled and burnished surfaces as the burnishing force rises. The tests determined an optimal burnishing force at a level of 500 N (lowest Ra = 0.24 μm). Further increase in the value of burnishing force turned out not to affect the surface roughness, which is consistent with the results obtained from experimental studies.
Keywords: Surface geometric structure, milling, burnishing, hybrid machining, FEM modeling
Read article »

   
© wydawnictwo.panova.pl